Pares de apriete

[Sauo_cid]

Buenas noches compañeros, me toca el cambio de bujias del Karoq 1.0 TSI. Bien el caso es que ando en busca de los pares de apriete para realizar el cambio, por mucho que he buscado no consigo localizar ningún manual o despiece que lo ponga.
A ver si alguien tiene idea de como conseguirlo.
Un saludo!

 

[Dave]

Buenas noches compañeros, me toca el cambio de bujias del Karoq 1.0 TSI. Bien el caso es que ando en busca de los pares de apriete para realizar el cambio, por mucho que he buscado no consigo localizar ningún manual o despiece que lo ponga.
A ver si alguien tiene idea de como conseguirlo.
Un saludo!

Hola @Sauo_cid

Para el Karoq 1.0 TSI ???
Creo que 22Nm

3.13.1 Replace spark plugs, 3-cylinder engines
– Remove air filter
– Remove air guide pipe
– Unlock and remove connectors from ignition coils -2-.
– Unscrew the fixing screws of ignition coils -1-.



– Press extractor -T10530- into the bore of the ignition coil -1- as far as it can go.
– Tighten the nut -2- in -direction of arrow- so that the extractor -T10530- stays firm in the bore of the ignition coil.



Remove ignition coil with extractor -T10530- in -direction of arrow- out of the camshaft housing.
– Undo nuts from the extractor -T10530- and remove from the bore of the ignition coil.
– Using the extractor -T10530- remove the other ignition coils out of the camshaft housing in sequence.
– Unscrew the ignition plugs with wrench - 3122 B- .



Installing

When installing new spark plugs, grease the ignition coils with power output stages with silicone paste ⇒ ETKA .
The correct silicone paste can be found under ignition coils and/or spark plugs in the ETKA.
– Unscrew spark plugs with spark plug wrench e. g. -3122 Band remove.
– Screw in new spark plugs with spark plug wrench e. g. -3122 B- and tighten to tightening torque ⇒ (See grid at the end) .
– Apply a thin adhesive bead -arrow- of silicone paste (from the ⇒ Electronic Catalogue of Original Parts ) all around the sealing hose of the ignition coil.
– Place all ignition coils loosely into the spark plug shaft.
– Align the ignition coils so that the fixing screws can be screwed in.
– Press ignition coils onto the spark plugs evenly by hand (do not use an impact tool).




– Screw in the ignition coils screws -1- and tighten to required tightening torque ⇒ (See grid at the end) .
– Attach plug connector for ignition coils -2-.
– Further assembly occurs in reverse order.




Fin

Nos envía a " Rep. gr. 28 ; Ignition system; Summary of components - ignition system "



28 – Ignition system
1 Ignition system
1.1 Assembly overview - ignition system



1 - Spark plug
❑ use spark plug wrench e.g. - 3122 B- for removing and installing
❑ When installing new spark plugs, grease the ignition coils with power output stage Pos. -2- with lubricating paste G 052 565 A1.
❑ Change interval: ⇒ Maintenance ; Booklet Karoq
❑ Observe part number ⇒ ETKA - Electronic Catalogue of Original Parts
❑ 22 Nm
2 - Ignition coil with power output stage
Ignition coil 1 with power output stage - N70-
Ignition coil 2 with power output stage - N127-
Ignition coil 3 with power output stage - N291-
❑ Removing and installing ⇒ “1.2 Removing and installing ignition coils with output stage”, page 249
❑ When installing new spark plugs, grease the ignition coils with power output stage with lubricating paste G 052 565 A1.
3 - Screw
❑ 8 Nm
4 - Knock sensor 1 - G61-
❑ Removing and installing ⇒ “1.3 Removing and installing knock sensor 1 G61 ”, page 251
5 - Screw
❑ The tightening torque influences the knock sensor function
❑ 20 Nm
6 - Hall sender 3 - G300-
❑ Outlet side camshaft sender
❑ Removing and installing ⇒ “1.4 Removing and installing Hall sender”, page 253
7 - Screw
❑ 8 Nm
8 - O-ring
❑ Check O-ring for damage
❑ O-ring is not available separately; in the event of damage, replace together with Hall sender 3 - G300- .
9 - Screw
❑ 8 Nm
10 - Hall sender - G40-
❑ Inlet side camshaft sender
❑ Removing and installing ⇒ “1.4 Removing and installing Hall sender”, page 253
11 - O-ring
❑ Check O-ring for damage
❑ O-ring is not available separately; in the event of damage, replace together with Hall sender - G40- .
12 - Sealing flange on the gearbox side
❑ Removing and installing ⇒ “2.3 Removing and installing sealing flange on gearbox side”, page 48
13 - Rotor
❑ Engine speed sender - G28-
❑ Removing and installing ⇒ “2.3 Removing and installing sealing flange on gearbox side”, page 48
14 - engine speed sender - G28-
❑ Removing and installing ⇒ “1.5 Removing and installing the engine speed sender G28 ”, page 254
15 - Screw
❑ 5 Nm


Un saludo.